DC8010 80x80x10mm Low-Profile DC Fan
A wide, thin 80mm fan for shallow displays, wall-mounted electronics and enclosures with limited rear clearance.
DC8010 spreads airflow across an 80mm opening while using only 10mm of installation depth. Three performance levels range from 14.49 to 21.74CFM, and the lowest-speed model is listed at 21.60dBA. Separate 5V, 12V and 24V families support different electronic platforms.
Rated Voltage: 5V / 12V / 24V
Size: 80x80x10mm
Max Airflow: 21.74CFM
Max Static Pressure: 1.77mmH2O
Rated Speed: 3,000RPM
Noise Range: 21.60-30.40dBA
5V, 12V and 24V Low-Profile Fan Options
Compare DC8010 by voltage, speed, airflow, static pressure, current, noise and bearing type. Select the required model from the full published specification table rather than choosing only by maximum airflow.
| Model | Bearing Type | Rate Voltage（VDC） | Current （A） | Speed （RPM） | Air Flow （CFM） | Static Pressure （mmH₂O） | Noise Level （dBA） | Weight （g） |
|---|---|---|---|---|---|---|---|---|
| YDH8010X05 | S or B | 5 | 0.26 | 3000 | 21.74 | 1.77 | 30.40 | 38 |
| YDM8010X05 | S or B | 5 | 0.15 | 2500 | 18.12 | 1.23 | 26.50 | 38 |
| YDL8010X05 | S or B | 5 | 0.13 | 2000 | 14.49 | 0.79 | 21.60 | 38 |
| YDH8010X12 | S or B | 12 | 0.08 | 3000 | 21.74 | 1.77 | 30.40 | 38 |
| YDM8010X12 | S or B | 12 | 0.07 | 2500 | 18.12 | 1.23 | 26.50 | 38 |
| YDL8010X12 | S or B | 12 | 0.05 | 2000 | 14.49 | 0.79 | 21.60 | 38 |
| YDH8010X24 | S or B | 24 | 0.15 | 3000 | 21.74 | 1.77 | 30.40 | 38 |
| YDM8010X24 | S or B | 24 | 0.10 | 2500 | 18.12 | 1.23 | 26.50 | 38 |
| YDL8010X24 | S or B | 24 | 0.09 | 2000 | 14.49 | 0.79 | 21.60 | 38 |
Low-Profile Cooling across an 80mm Airflow Area
DC8010 prioritizes shallow installation, broad air coverage and a usable low-noise operating option.
Only 10mm Deep
The shallow frame preserves internal clearance for boards, connectors and cable routing in thin products.
Broad 80mm Air Coverage
A larger face area distributes moderate airflow across wider heat sources instead of concentrating it in a small jet.
Low-Speed Acoustic Option
The 2,000RPM variant is listed at 21.60dBA for applications where moderate airflow and reduced noise are preferred.
5V, 12V and 24V Choices
Multiple voltage families simplify use across consumer electronics, embedded systems and industrial controls.
80x80x10mm Low-Profile DC Fan Overview
An 80mm face distributes airflow across a wider area, while the 10mm frame keeps the assembly thin. This trade-off favors moderate-resistance enclosures rather than dense filters or long ducts.
Glass-fiber-reinforced PBT impeller and housing are rated UL 94V-0. Available functions include FG, RD, PWM, Auto Restart and Polarity Protection; final wiring, connector, signal definition and bearing choice should be confirmed for the project.
Airflow and Noise Choices for the DC8010
This low-profile 80mm fan is intended for moderate-resistance airflow paths. Read the curve together with the enclosure geometry: a blocked inlet or tight exhaust can reduce delivered airflow enough that the 10mm format is no longer the right mechanical choice.
Shallow-Enclosure Uses for an 80mm Fan
Use cases center on shallow products that benefit from broad, moderate airflow and controlled acoustics.
Get Fan Selection Support
Thin Displays and Signage
The 10mm profile works behind displays and digital signage where cabinet thickness is tightly constrained.
Set-Top Boxes and Media Devices
Wide, gentle airflow can cover processors, tuners and power sections within low-profile media enclosures.
Wall-Mounted Control Panels
DC8010 can ventilate shallow wall-mounted panels without consuming the depth needed for wiring terminals.
Network Edge Devices
Routers and edge gateways with a broad PCB and limited vertical clearance can evaluate the 12V or 24V variants.
Quiet Instrument Enclosures
Lower-speed models suit instruments where heat load is moderate and operating noise must remain controlled.
80x80x10mm Low-Profile Fan Noise and Airflow Video
Use a shallow enclosure to show why the 10mm frame is selected, and record operating sound only with the model, distance and test condition stated. Show inlet and outlet clearance so the airflow result has context.
Use a shallow enclosure to show why the 10mm frame is selected, and record operating sound only with the model, distance and test condition stated. Show inlet and outlet clearance so the airflow result has context.
80mm Low-Profile Fan Selection FAQs
A: DC8010 uses a 80x80x10mm frame. Confirm mounting-hole spacing and clearance with the product drawing before installation.
A: Published options include 5V / 12V / 24V. Select the exact model according to rated voltage, current and controller compatibility.
A: The published range reaches 21.74CFM and 1.77mmH2O. Use the P-Q curve for the actual operating point.
A: FG, RD and PWM are listed as function options. Signal voltage, frequency, wiring and minimum duty must be confirmed before connection.
A: The product range lists sleeve or ball bearing. Confirm the bearing code, operating temperature and expected service conditions with the selected model.
A: Project-specific voltage, speed, wire length, connector and control functions can be discussed. Performance must remain tied to an approved model and sample validation.
Can't Find the Perfect Fan?
We offer customization services from wire length to full mold design. Get a solution in 48 hours.
Get Fan Selection Support